Ethernet vs Wi-Fi, Which Should You Use at Home?

Xfinity says to use Ethernet for desktops, gaming consoles and streaming devices. TP-Link lists Wi-Fi 7 at up to 46 Gbps but says actual wireless throughput is not guaranteed.

Technobezz
Ethernet vs Wi-Fi, Which Should You Use at Home?Image: TP-Link

Contents

Don't Miss the Good Stuff

Get tech news that matters delivered to your inbox.

For high-bandwidth devices, internet providers point to the cable. Xfinity says a wired connection can help reduce lag and improve speed, and AT&T says wired connections consistently give its best performance. TP-Link lists a maximum data rate of 46 Gbps for Wi-Fi 7, but it says actual wireless throughput is not guaranteed.

Ethernet vs Wi-Fi at a glance

  • Ethernet speed: NETGEAR's installation guide for its GS110EMX switch lists Cat5e or higher for 1, 2.5 and 5 Gbps connections at up to 100 meters, and Cat6a or higher for 10 Gbps at up to 100 meters.
  • Wi-Fi speed: TP-Link's comparison table lists maximum data rates of 9.6 Gbps for Wi-Fi 6, 9.6 Gbps for Wi-Fi 6E and 46 Gbps for Wi-Fi 7. These are TP-Link's figures.
  • Lag: Xfinity says a wired connection can help reduce lag. The FCC says several wireless devices on the same Wi-Fi network can affect performance and create lag or slower responses.

Speed on paper and speed at home

TP-Link's 46 Gbps figure for Wi-Fi 7 comes from a calculation that assumes a 320 MHz channel and 16 spatial streams. TP-Link describes its maximum wireless signal rates as physical rates derived from the IEEE 802.11 specifications.

The same TP-Link page says actual throughput and coverage are not guaranteed. It says they vary with network conditions, client limitations, building materials, obstacles, traffic and where the client sits.

NETGEAR's guide for the GS110EMX permits Cat6 for 10 Gbps when the cable is shorter than 55 meters. AT&T recommends a Cat5e or better Ethernet cable. See What Is Ethernet?

Lag, interference and when providers say to plug in

The FCC says that when multiple wireless devices use the same Wi-Fi network, it can affect performance and create lag. It also says neighboring networks can affect performance on the 2.4 GHz band, and TP-Link's router speed test guide calls nearby Wi-Fi networks a major source of interference. See 2.4 GHz vs 5 GHz Wi-Fi.

TP-Link advertises Wi-Fi 7 latency as four times lower than Wi-Fi 6 and 6E routers, and it identifies the supporting data as laboratory test results. That is a relative claim from the maker, not a home latency guarantee.

Xfinity's home network advice is to use Ethernet for high-bandwidth devices. It names desktop computers, gaming consoles and streaming devices, connected directly to the gateway or router.

For its most accurate speed test result, Verizon recommends connecting the device directly to the router with an Ethernet cable if possible, disconnecting any VPN and avoiding streaming during the test. TP-Link's guide calls for one computer on Ethernet and a second device on Wi-Fi, so the two results can be compared.

If running a cable is not practical

Two alternatives use wiring a home already has. TP-Link says powerline turns a home's electrical wiring into network cables, and a basic network needs at least two powerline devices. It says the devices should share an electrical circuit, and it recommends wall outlets because power strips may filter the signal and affect performance.

TP-Link specifies its TL-PA9020P KIT at up to 2000 Mbps, a theoretical physical layer rate, while the Ethernet ports on it are 10/100/1000 Mbps. TP-Link says actual speeds can be limited by the Ethernet ports, traffic, electrical noise and wiring issues.

MoCA uses coaxial cable instead. Verizon's MoCA Ethernet Adapter user guide says MoCA 2.5 can deliver up to 2.5 Gbps of wired speed through existing home coaxial wiring. Verizon says MoCA is less prone to interference than Wi-Fi, but bandwidth is shared by all the MoCA devices on the same network. Verizon lists the adapter at $99.99 each, as of November 2026.

Which one fits

If the device is a desktop computer, a gaming console or a streaming box, Ethernet fits, because those are the devices Xfinity says to connect directly. If you want to know whether your plan delivers its speed, test over a cable first, since that is the setup Verizon recommends for its most accurate result.

If a device stays on Wi-Fi, the FCC names two things that can affect its performance, the number of wireless devices on the same network and neighboring networks. See Is Wi-Fi 7 Worth It?

If running a cable is not practical and the home has coax outlets, MoCA is an option, because Verizon says its adapter uses existing home coaxial wiring. If both ends can share an electrical circuit, powerline is an option, because TP-Link says it carries network signals over a home's electrical wiring. Both come with the limits their makers state.

Share