How to Fix a Failed Wireless Connection on a Samsung TV

Fix a Samsung TV wireless connection failed error by restarting your TV and router, checking the Wi-Fi password, and resetting network settings.

Contents

Don't Miss the Good Stuff

Get tech news that matters delivered to your inbox.

To fix a failed wireless connection on your Samsung TV, restart the TV and router, reconnect with the correct Wi-Fi password, and reset the TV’s network settings if it still cannot connect. Check Network Status to see whether the failure is between the TV and router or between the router and internet.

The network paths below use Samsung’s Connection menu, with diagnostic and network reset steps for supported 2022 and newer models. Menu labels vary by model and region; some Samsung manuals, for example, list Connections instead of Connection and Network Settings instead of Open Network Settings, so check your model’s manual when your menus differ.

The short version

  • Restart both devices: Unplug the TV and router for 30 seconds, reconnect them, and allow several minutes for networking to recover.
  • Check the password: Verify capitalization and test the same password on another device.
  • Isolate the failure: Test another device on your home network and connect the TV to a compatible phone hotspot.
  • Reset networking: Resetting clears the TV’s network configuration, so use Reset Network when you are ready to reconnect.

Fix or checkWhen to use it
Restart TV and routerStart here when the wireless connection fails
Cold boot with the remoteRestart the TV by holding Power
Cold boot without the remoteDisconnect TV power for 30 seconds
Network Status and RetryIdentify which connection fails
Check another deviceDetermine whether the home network also fails
Enable Wi-FiYour model exposes a wireless switch
Verify the passwordThe TV cannot join a protected network
Reconnect wirelesslyYou have confirmed the network credentials
Add NetworkYour network name is hidden
Enable SSID broadcastingYou want the hidden network to appear
Improve receptionThe signal is weak or intermittent
Try another frequency bandThe TV supports both router bands
Reduce network loadOther devices or activities congest the connection
Check router restrictionsThe failure followed a router setting change
Update router firmwareCompatibility problems persist
Delete the saved networkYour model offers Manage Saved Networks
Reset NetworkReconnect after clearing network configuration
Try a phone hotspotSeparate the original network from the TV fault
Connect EthernetUse a wired workaround on a supported TV
Set manual DNSThe TV joins Wi-Fi but has internet or DNS failures
Correct the clockThe TV’s time is incorrect
Configure an IP address manuallyA network administrator provides valid settings
Update TV software onlineA working connection is available
Update TV software through USBYour model supports offline firmware updates
Run Device CareYour model offers general diagnostics
Run the Smart Hub connection testNetworking works but smart services fail
Reinstall an appOnly one app fails
Reset Smart HubSmart Hub or service failures persist
Factory resetOther checks have not resolved a TV-side fault
Contact Samsung SupportThe TV still cannot connect after troubleshooting

Restart your TV and router

Unplug both the TV and router from their electrical outlets for 30 seconds. Reconnect them, switch them on, and allow several minutes for networking to recover before trying Wi-Fi again.

You can also cold boot your Samsung TV with the remote. With the TV on, hold Power until the TV switches off and restarts. Without the remote, disconnect the TV from its outlet for 30 seconds, then reconnect it.

Find where the connection fails

On supported 2022 and newer models, open Settings > All Settings > Connection > Network > Network Status, then select Retry. An X between the TV and router identifies a local connection problem. An X between the router and internet points toward your internet service.

Test internet access on another device connected to the same router. If multiple devices cannot get online, contact your internet provider. If the other device works, continue with the TV’s wireless settings.

Check Wi-Fi and reconnect with the correct password

On models with a Wi-Fi switch, open Settings > All Settings > Connection > Network > Expert Settings and enable Wi-Fi. Otherwise, continue to wireless network selection.

Check the password’s capitalization and test the same password on another device. If the router’s password has never been changed, check its label before entering it on the TV.

Open Settings > All Settings > Connection > Network > Open Network Settings > Wireless. Choose your network and enter its password, then select Go and OK. Some regional keyboards use Done instead of Go.

For a hidden network, choose Add Network on the Wireless screen and enter its SSID and credentials. Alternatively, enable SSID broadcasting in the router’s administration interface, then retry the connection. Router menu labels vary by model.

Improve the signal and check the router

Bring the router nearer the TV and reduce obstacles and electronic interference between them to improve a weak Wi-Fi signal. Installing a Wi-Fi repeater is another option for weak or intermittent reception. Retry the connection after improving the signal.

If your TV supports both frequency bands, test the router’s 2.4 GHz and 5 GHz networks. Check the TV’s model specifications before trying both. On a congested home network, disconnect other devices and pause bandwidth-heavy activities, then retest the TV.

When the failure started after a router setting changed, reverse the associated change and try again. Ask your internet provider or router manufacturer to check restrictions and bandwidth allocation if the problem continues. For compatibility problems, including failed WPS connections, follow the router manufacturer’s firmware update procedure through its administration interface or app.

Clear the saved connection or reset networking

Deleting a saved network removes that saved connection from the TV. On models with Manage Saved Networks, open All Settings > Connection > Network > Open Network Settings > Wireless > Manage Saved Networks. Choose your network, select Delete, and reconnect with the verified password.

If that control is missing or reconnecting still fails, use the network reset on supported 2022 and newer models. Resetting the network clears the TV’s network configuration. Open Settings > All Settings > Connection > Network > Reset Network, then select Reset. Then go to the TV’s network settings and set up the wireless connection again.

Try a hotspot or wired connection

Enable a compatible phone hotspot and connect the TV to it through Open Network Settings > Wireless. If the TV connects successfully, the original network is the problem. Focus further troubleshooting on the home router and internet connection.

For a TV with wired-network support, connect the router to the LAN port on the TV or its One Connect Box. Open Settings > All Settings > Connection > Network > Open Network Settings > Wired, then select OK. Ethernet bypasses Wi-Fi and can provide a working connection for a software update, but it does not repair the wireless radio.

Check DNS and time when Wi-Fi connects

Use a manual DNS server when the TV has joined the network but has an internet or DNS failure. Open All Settings > Connection > Network > Network Status > IP Settings > DNS Setting. Choose Enter Manually, open DNS Server, enter 8.8.8.8, and select Done on the number selector.

If the TV’s time is incorrect, open All Settings > General & Privacy > System Manager > Time > Clock. Correct the time or set Clock Mode to Auto, then retry internet access.

For an IP configuration problem, use manual settings only with valid values from your network administrator. Open All Settings > Connection > Network > Network Status > IP Settings and change Get Automatically to Enter Manually. Open IP Address, enter the address your administrator assigned, then select Done and OK.

Update the TV software

With a working connection, open Settings > All Settings > Support > Software Update > Update Now. Leave the TV powered until the update finishes. If a running app makes the update option unavailable, switch to the TV source and try again.

For models that support USB updates, find your exact TV model on Samsung’s Manuals & Software page and download its firmware. Extract it to an empty FAT32 USB drive without adding enclosing folders. The same page provides the model-specific manual for checking menu differences.

Insert the USB drive into the TV, then open Settings > All Settings > Support > Software Update > Update Now. Select Yes when prompted and keep power connected until installation finishes. Retry the wireless connection afterward.

Run diagnostics before a factory reset

On models offering general diagnostics, open Settings > All Settings > Support > Device Care > Start Device Care. If networking works but smart services still fail, continue with the Smart Hub connection test.

On models with Smart Hub diagnostics, open Settings > Support > Device Care > Self Diagnosis > Start Smart Hub Connection Test. On models that omit Device Care, go directly from Support to Self Diagnosis. Review the internet, ISP, Samsung-server, and app-service results, then select Close.

If only one app fails while networking works, reinstall that app. Deleting the app removes it, and you will need to sign back in after reinstalling. Open Apps > Settings, choose the affected app, and select Delete. Press Return, open Search, find the app, and select Install; if Delete is unavailable, select Reinstall instead.

For persistent Smart Hub or service failures, resetting Smart Hub removes its accounts, apps, and related settings. Open Settings > Support > Device Care > Self Diagnosis > Reset Smart Hub, omitting Device Care on models without that menu. Enter the TV PIN and select OK after completion. The default PIN is 0000 on models before 2025 unless changed; 2025 and newer models use the PIN created during initial setup.

Consider a factory reset of your Samsung TV only as a last resort for a persistent TV-side fault. A factory reset requires you to restore app sign-ins and settings. Exit running apps, then open Settings > General & Privacy > Reset, labeled Factory Data Reset on some models. Some models place Reset under Settings > Support > Self Diagnosis.

Enter your TV PIN, then select Reset and OK. The default PIN is 0000 on models before 2025 unless you changed it; on 2025 and newer models, use the PIN created during initial setup. Complete setup again, and contact Samsung Support if the TV still cannot connect after troubleshooting and resetting.

Frequently Asked Questions

Can you connect the TV using WPS?

Yes, if both your TV and router support WPS; check your exact TV manual because Samsung’s regional menu path may differ. Enable WPS in the router’s administration interface, then open the TV’s Wireless network list and choose its WPS option, labeled WPS Connection or Use WPS depending on the model. Hold the router’s WPS button for 2 to 3 seconds until its indicator flashes, then press OK after connection.

Where can you find the TV’s MAC address for router troubleshooting?

Open Settings > All Settings > Support > About TV, or About This TV, and scroll to the MAC address. Give it to the person administering your network for identification and access troubleshooting.

Can SmartThings transfer your phone’s Wi-Fi settings to the TV?

Yes, compatible TVs offering Smartphone setup can receive your phone’s Wi-Fi configuration during setup, including after a reset; Samsung’s official SmartThings page helps you locate the companion app. Connect your phone to the desired Wi-Fi network and sign into SmartThings, then select Smartphone during TV setup and scan the QR code. Choose the location and room, then tap Next to transfer the configuration. Review the displayed terms and, if accepting, tap I Agree to all, then tap Ok.

How can you enable automatic TV software updates after reconnecting?

On an internet-connected Samsung smart TV, open Settings > All Settings > Support > Software Update and enable Auto Update. Use this maintenance setting after connectivity is restored.

Does a Samsung account fix a failed wireless connection?

Samsung account setup provides access to smart services after networking works; it does not repair wireless association. During remote-based setup, review the Smart Hub terms and, if accepting, select I Agree to all, then select Ok. At account setup, select Use Existing Account or Create New Account and complete sign-in.

Can Samsung help remotely if Wi-Fi still fails?

Samsung Remote Management requires a supported smart TV with a working internet connection, potentially through Ethernet, and availability varies by region. Contact Samsung customer care, then open Home > Settings > All Settings > Support > Remote Management and enable it. Select View Terms, review the terms, and select Close. Give the displayed eight-digit PIN to the Samsung representative.

Share