How to Fix a Monitor That Is Not Displaying Anything

For a monitor display not working, check power, select the correct input, reconnect the video cable, then test the computer’s display output.

Contents

Don't Miss the Good Stuff

Get tech news that matters delivered to your inbox.

To fix a monitor that is not displaying anything, check its power, select the input matching your video cable, and reconnect the cable at both ends. Then isolate the cable, monitor, and computer before changing display settings or drivers. The Windows steps below use Windows 11 menus.

The short version

  • Power first: Check the monitor’s power connections and outlet before changing computer settings.
  • Match the input: Select the monitor input corresponding to the connected video cable.
  • Isolate the fault: Change one cable, port, monitor, or computer at a time.
  • Check computer output: On Windows 11, press Windows + P and choose Duplicate or Extend.
  • Escalate hardware failures: Contact the manufacturer if power checks and the monitor’s own diagnostic still fail.

FixWhen to try it
Check power connections and outletDell or Alienware monitor will not turn on
Discharge monitor powerSupported Dell monitor remains without power
Increase brightnessDisplay brightness may be too low
Wake the computer and select the inputMonitor has power but no computer picture
Open the monitor menu and reconnect videoSamsung monitor stays blank
Use the graphics card’s outputDesktop has a separate graphics card
Bypass the dock and check cable compatibilityMac display connects through a dock or adapter
Swap the cable, port, monitor, or computerWindows 11 connection checks do not help
Disconnect nonessential peripheralsComputer shows a black screen during startup
Run the monitor’s self-testDell or Alienware monitor supports the diagnostic
Run Picture TestSamsung monitor offers Self Diagnosis
Change Windows projection modeWindows 11 external output stays blank
Reset the Windows graphics driverWindows 11 screen remains blank
Detect the Windows displayAnother screen works on the Windows 11 PC
Restore a supported Windows resolutionPicture disappeared after a resolution change
Restore a supported Windows refresh rateSelected rate exceeds the monitor’s supported timing
Restart or power-cycle WindowsWindows remains blank or unresponsive
Use low-resolution startup or Safe ModeWindows display settings or drivers need repair
Detect or reconnect the Mac displayMac does not recognize the external screen
Approve the Mac accessoryApple-silicon laptop requests display approval
Check Mac display limitsConnected displays exceed the supported configuration
Undo a Mac resolution changeScreen went blank immediately after changing resolution
Start an Apple-silicon Mac in safe modeResolution recovery needs a usable display
Install DisplayLink ManagerDock, adapter, or monitor explicitly uses DisplayLink
Complete DisplayLink permissionsDisplayLink Manager needs its required permissions
Enable Chromebook mirroringConnected monitor should show the built-in screen
Correct Chromebook display and cable settingsExternal display configuration needs adjustment
Install Windows updatesWindows 11 display access is available
Update the graphics driverWindows hardware checks pass but the problem remains
Get applicable Dell updatesDell offers a package for the exact product
Update macOS and Apple display firmwareCompatible Mac has an update available
Update Samsung monitor firmwareFirmware is available for the exact monitor model
Request hardware servicePower checks and isolated monitor tests fail

Check the monitor’s power and brightness

For a Dell or Alienware monitor with no power, reseat the power cable at both ends, including any external adapter connections. Test the outlet with a working lamp, bypass the power strip, and press the monitor’s Power button. For another brand, follow its manual’s corresponding power checks.

If the Dell or Alienware monitor still will not turn on, try a compatible replacement power cable or an adapter matching its specifications. For Dell monitors covered by its power troubleshooting instructions, Dell also recommends disconnecting monitor power at both ends, holding the Power button for 30 seconds, then waiting one minute. Reconnect directly to a wall outlet, press Power, and allow up to five seconds.

Increase brightness using the monitor’s physical controls. For a supported Apple display, open Apple menu > System Settings > Displays and adjust the brightness control.

Select the correct input and reconnect the cable

Move the mouse to wake the computer, then use the monitor’s buttons or joystick to select the input matching your connected cable. Input names and button sequences vary by model. On a Samsung monitor, press a monitor button to bring up its menu, pressing Power first if necessary.

Samsung recommends connecting the computer with only one video cable and disconnecting and reconnecting that cable at both ends. On a desktop with a separate graphics card, connect the monitor to that card’s video output. Motherboard video-output availability depends on the processor and system configuration.

For a Mac connected through a dock, connect the display directly to the Mac. Check that the cable and adapter support the intended resolution and refresh rate, including the relevant DisplayPort Alt Mode or Thunderbolt connection for USB-C adapters. A USB-C connector by itself does not establish video compatibility.

Isolate the hardware and run monitor diagnostics

With a Windows 11 external display, try a known-working video cable, then another video-output port on the computer. Change one component at a time so you can identify which change restores the picture. If neither helps, connect the monitor to another computer and connect another monitor to the original computer.

For a black screen during startup, turn off the computer and disconnect nonessential USB devices, storage, printers, and VR equipment. Leave the keyboard, mouse, and monitor connected. Restart the computer, then reconnect devices individually if the picture returns.

For a Dell or Alienware monitor with the documented self-test feature, turn off the monitor, disconnect its video cable, and turn it on again. Look for its self-test or no-signal screen. If that screen does not appear, contact monitor support.

On a Samsung monitor offering Self Diagnosis, open Menu, or open Settings (labeled All Settings on some models). Depending on the model, go through Support or System to Self Diagnosis, sometimes under Device Care. Select Picture Test, select OK, and let the test finish without changing inputs.

Restore Windows display output

On Windows 11, press Windows + P and select Duplicate or Extend. When you cannot see the projection menu, Microsoft recommends pressing Windows + P, then P, then Enter to change the projection mode.

Next, press Windows + Ctrl + Shift + B to reset the graphics driver. A beep or brief flicker can indicate that the reset occurred. If you have a working screen, open Start > Settings > System > Display > Multiple displays and select Detect.

If the monitor went blank after a display-mode change, use another working screen to open Start > Settings > System > Display. Select the affected display and choose the Display resolution option marked (Recommended). For refresh rate, open Advanced display, select the affected monitor, and use Choose a refresh rate to select a rate supported by that monitor.

When you can use Windows, restart through Start > Power > Restart. If necessary, choose Shut down and turn the PC on again.

Forcing an unresponsive PC to turn off can lose unsaved work. If the computer is unresponsive, hold its Power button for 20 seconds, then turn it on again.

Recover Windows display access

If you need a usable screen to repair Windows 11 display settings or drivers, use low-resolution startup or Safe Mode. When you can access Windows Recovery Environment, select Troubleshoot > Advanced options > Startup Settings > Restart. An encrypted device may require its BitLocker recovery key.

Press 3 or F3 for Enable low-resolution video, or press 4 or F4 for Enable Safe Mode. Use the recovered display to restore a supported resolution or repair the graphics driver with the steps below.

Reconnect and detect a Mac display

On a Mac with a usable screen, open Apple menu > System Settings > Displays. Hold Option and click Detect Displays. Alternatively, disconnect and reconnect the display’s power and video connections, or put the Mac to sleep and wake it.

For an Apple-silicon Mac laptop with accessory approval enabled, unlock the Mac and reconnect the display. Click Allow in the accessory prompt. Also check your Mac model’s display specifications, disconnect excess displays, and reduce resolution or refresh-rate combinations that exceed its supported configuration.

If the picture disappeared immediately after changing the Mac’s resolution, wait 15 seconds, then press Esc if it does not revert. On an Apple-silicon Mac, you can next shut down and hold the Power button until startup options appear. Select the startup volume, hold Shift, and click Continue in Safe Mode.

Once you have a usable display in safe mode, open Apple menu > System Settings > Displays and click Default. Restart normally afterward. This resolution recovery applies specifically when changing the resolution caused the blank screen.

For a dock, adapter, or monitor explicitly using DisplayLink technology, get the compatible DisplayLink Manager download. Install it and connect the DisplayLink device. Ordinary native USB-C displays do not require this application.

At Allow Screen Recording, click Open System Settings and enable the permission for DisplayLink Manager. Restart the app, then enable Background Activity through the wizard’s Open System Settings button if requested. Click Finish to complete the wizard.

Check Chromebook display settings

On a supported Chromebook with a connected monitor, select the time, then open Settings > Device > Displays. Select Mirror Built-in Display to mirror the built-in screen. That option appears only when a monitor is connected.

Within Displays, select the external monitor and choose a supported Resolution and refresh rate. Check that the adapter matches the computer’s output and monitor’s input ports, and that the USB-C cable supports the required display connection. External-display limits depend on the Chromebook model.

Update graphics drivers and display software

Once you have usable display access on Windows 11, open Start > Settings > Windows Update and select Check for updates. Install applicable updates and restart when required. If the display problem remains, find and update your graphics driver through Device Manager.

Expand Display adapters, right-click the graphics adapter, and select Update driver, then choose the option to search automatically for drivers. A working secondary screen or Safe Mode may be necessary to reach these controls.

For a supported Dell product, open Dell Drivers & Downloads and identify it by Service Tag or model. Obtain only the applicable graphics driver, BIOS, monitor firmware, or dock update, and follow that package’s model-specific instructions. Available packages vary by product.

On a compatible Mac, open Apple menu > System Settings > General > Software Update and install the compatible update offered. Apple display firmware arrives through macOS updates. Keep the Mac awake and its lid open during installation.

Samsung also identifies monitor firmware updates as a possible blank-screen fix. Find your exact model in Samsung Manuals & Software, check for firmware, and follow its supplied installation instructions. Firmware availability varies by model.

Request repair when hardware checks fail

If power checks and isolated monitor tests still fail, contact the manufacturer for model-specific service. For Dell, select Check Support Status using the Service Tag or Express Service Code, then contact technical support with the model and troubleshooting results. Do not open the monitor.

Frequently Asked Questions

What should you try when a black Windows screen still shows the cursor?

On Windows 11, press Ctrl + Shift + Esc to open Task Manager, right-click Windows Explorer, and select Restart. You can also press Ctrl + Alt + Delete to reach Task Manager. This addresses a stalled desktop, not a monitor reporting no signal.

Why does the external display stop working when you close a Mac laptop?

Closed-lid use requires connecting the Mac laptop to power and attaching an external keyboard and mouse. On an Apple-silicon Mac laptop with accessory approval enabled, approve the keyboard and mouse before closing the lid. Your Mac model’s external-display limits still apply.

How do you reconnect a wireless monitor in Windows 11?

For a PC and display or adapter supporting Miracast, turn on Wi-Fi through the taskbar’s Network, Sound, or Battery panel and turn on the receiving display or adapter. Press Windows + K and select it. Restart both devices if the connection still fails.

What can you try when a Chromebox displays nothing during setup?

After connecting and powering on the Chromebox, press Ctrl + Full screen (F4) to cycle its display options. This shortcut applies specifically to Chromebox setup.

Why do DisplayLink monitors stop working after you log in?

DisplayLink Manager may not be running. Open Finder > Applications > DisplayLink Manager, open its menu-bar icon, and select Launch automatically after logging-in. This applies to macOS displays using DisplayLink technology.

How can you change accessory approval on an Apple silicon Mac laptop?

Open Apple menu > System Settings > Privacy & Security > Accessories > Allow accessories to connect. Choose the appropriate approval behavior, such as Automatically allow when unlocked. On a supervised Mac, ask the administrator to review the managed accessory setting.

What does it mean when DisplayLink says the system stopped the screens?

For DisplayLink Manager using ScreenCaptureKit on macOS Sequoia 15 and later, the vendor’s fix for this message is to free startup-disk space until at least 25 GB is available. Apply this space requirement when that specific message appears.

What must you enable when another Windows PC is the wireless monitor?

On a compatible receiving PC, ensure the Wireless Display optional app is installed and open it from taskbar search. Open Settings > System > Projecting to this PC and configure discoverability. These steps apply to a PC acting as a Miracast receiver.

Share