The Beats Studio Pro cutting out mid-song feels like a split-second glitch, audio drops for half a beat, then comes right back. It happens most often when you're walking around the house or sitting near a WiFi router. The good news is it's almost never a hardware failure. A few tweaks to how the headphones talk to your phone usually fix it.
## Start With a Bluetooth Reset
The quickest test: forget the Beats Studio Pro from your phone's Bluetooth list, then pair them fresh. On an iPhone, go to Settings > Bluetooth, tap the blue "i" next to Beats Studio Pro, and choose Forget This Device. On Android, open Settings > Connected devices > tap the gear icon next to Beats Studio Pro and hit Forget.
Now put the headphones in pairing mode: press and hold the system button (the power button on the right earcup) until the Fuel Gauge LEDs start pulsing white. Reconnect from your phone's Bluetooth menu. If the cutting out stops, a corrupt saved pairing record was the culprit.
## Move Away From Interference Sources
Bluetooth runs on the 2.4 GHz band, same as most WiFi networks, microwaves, and wireless baby monitors. If you're sitting next to a running microwave or have an old router broadcasting both 2.4 and 5 GHz, the airwaves get crowded and your headphones will stutter.
Walk outside or into a room with no electronics. If the connection steadies immediately, you found the interference. The fix is usually moving your WiFi router away from your listening spot, switching to 5 GHz only on devices that support it, or just staying a few feet away from the microwave while it's on.
Check for Charging Port Debris
Known issue on the Studio Pro: sweat can seep into the USB-C port over time. Even a tiny bit of corrosion or lint inside the port can confuse the headphones' power management, which sometimes triggers Bluetooth dropouts. Take a look at the USB-C port on the left earcup for any gunk. Use a dry toothpick or a plastic SIM eject tool to gently clean it out. Compressed air works too. Don't use anything metal.
Once it's clean, test the connection again. This fix alone solves the cutting-out issue for a lot of Studio Pro owners, especially if you wear them during workouts.
Update Firmware Through the Beats App
Beats has shipped firmware updates that improve Bluetooth stability on the Studio Pro. On Android, open the Beats app and check for updates. On iOS, firmware updates happen automatically when the headphones are connected to your iPhone and in range, but you can nudge them by going to Settings > Bluetooth, tapping the "i" next to Beats Studio Pro, and checking for a firmware version number.
The headphones need to be on (worn or held), with at least 50% battery, and your phone needs to stay within a few feet during the update. It takes about five minutes. After it finishes, test the connection for dropouts.
Disable Spatial Audio for Stereo Tracks
Spatial Audio on the Studio Pro can make normal stereo music sound hollow or phasey, and some users report that the processing overhead causes brief audio cuts. Try turning it off: press the b button on the right earcup until the voice prompt says "Spatial Audio off" (you'll cycle through ANC, Transparency, and off). Or on your source device, go to Settings > Bluetooth > Beats Studio Pro and disable Spatial Audio there.
If the cutting stops, leave it off. The Studio Pro sound great in standard stereo mode, and you lose nothing by skipping the spatial processing on non-Atmos content.
Try a Wired Connection Over USB-C
If the Bluetooth cutting out is driving you crazy, plug the Studio Pro into your phone or computer with a USB-C cable. The headphones support lossless audio over USB-C, and wired mode bypasses Bluetooth entirely. You'll need the Beats app version 1.6 or later for full USB-C audio support, so update first.
Wired audio is bulletproof. If the cutting out disappears over USB-C, you know the issue is purely Bluetooth-related and not a headphone hardware fault.
Reset the Headphones
If you've tried everything else, a full reset clears any internal state that might be causing recurrent dropouts. Press and hold the system button (power button on the right earcup) for 10 seconds. The Fuel Gauge LEDs will flash white, then one LED flashes red in a sequence that happens three times. Once the lights stop, the headphones reset and automatically turn back on.
After the reset, re-pair with your phone from scratch. This clears any lingering corruption from previous pairings or firmware glitches.
Test With a Different Source Device
If the cutting out only happens with your phone but not with your laptop or friend's phone, the problem lives on that phone's Bluetooth controller. Restart the phone, clear its Bluetooth cache (if on Android: Settings > Apps > Show system > Bluetooth > Storage > Clear cache; on iOS: restart the phone or reset network settings in Settings > General > Transfer or Reset iPhone > Reset > Reset Network Settings).
If the dropouts persist across all devices, you may be dealing with a hardware issue, but that's rare. The steps above resolve it in nearly every case.
